Hackpads are smart collaborative documents. .

Clarence Lee

353 days ago
Unfiled. Edited by Clarence Lee 353 days ago
  1.    新版本Marlin from Johann [deltabot] branch  已支援z-offset, 雷射模組, M665, M666等
 
578 days ago
Unfiled. Edited by Clarence Lee 578 days ago
  1. 注意噴嘴不要停止在ZP上噴頭還是熱的
Clarence L
  1. 下面一定要有玻璃或其他材質硬板,要凹到中央下方微突起朝下,周圍用夾子夾才會平整(請細看下面的影片解說)
  1. 詳讀本說明
 
 
 
 
312 days ago
Unfiled. Edited by Clarence Lee 312 days ago
  1. 網頁  那邊 我們會需要用到M665 的L R Z 三個值
 
 
 
 
920 days ago
Unfiled. Edited by Clarence Lee 920 days ago
    This file is part of Repetier-Firmware.
 
    Repetier-Firmware is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.
 
    Repetier-Firmware is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.
 
    You should have received a copy of the GNU General Public License
    along with Repetier-Firmware.  If not, see <http://www.gnu.org/licenses/>.
 
*/
 
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
 
/**************** READ FIRST ************************
 
   This configuration file was created with the configuration tool. For that
   reason, it does not contain the same informations as the original Configuration.h file.
   It misses the comments and unused parts. Open this file file in the config tool
   to see and change the data. You can also upload it to newer/older versions. The system
   will silently add new options, so compilation continues to work.
 
   This file is optimized for version 0.91
 
   If you are in doubt which named functions use which pins on your board, please check the
   pins.h for the used name->pin assignments and your board documentation to verify it is
   as you expect.
 
*/
 
#define NUM_EXTRUDER 1
#define MOTHERBOARD 33
 
#include "pins.h"
 
// ################## EDIT THESE SETTINGS MANUALLY ################
// ################ END MANUAL SETTINGS ##########################
 
#define FAN_BOARD_PIN -1
#define X_MIN_PIN -1
#define Y_MIN_PIN -1
 
//#define EXTERNALSERIAL  use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer.
// Uncomment the following line if you are using arduino compatible firmware made for Arduino version earlier then 1.0
// If it is incompatible you will get compiler errors about write functions not beeing compatible!
//#define COMPAT_PRE1
#define MIXING_EXTRUDER 0
 
#define DRIVE_SYSTEM 3
#define XAXIS_STEPS_PER_MM 80
#define YAXIS_STEPS_PER_MM 80
#define ZAXIS_STEPS_PER_MM 80
#define EXTRUDER_FAN_COOL_TEMP 50
#define PDM_FOR_EXTRUDER 1
#define PDM_FOR_COOLER 1
#define DECOUPLING_TEST_MAX_HOLD_VARIANCE 20
#define DECOUPLING_TEST_MIN_TEMP_RISE 1
#define RETRACT_ON_PAUSE 2
#define PAUSE_START_COMMANDS ""
#define PAUSE_END_COMMANDS ""
#define EXT0_X_OFFSET 0
#define EXT0_Y_OFFSET 0
#define EXT0_STEPS_PER_MM 100
#define EXT0_TEMPSENSOR_TYPE 8
#define EXT0_TEMPSENSOR_PIN TEMP_0_PIN
#define EXT0_HEATER_PIN HEATER_0_PIN
#define EXT0_STEP_PIN ORIG_E0_STEP_PIN
#define EXT0_DIR_PIN ORIG_E0_DIR_PIN
#define EXT0_INVERSE 0
#define EXT0_ENABLE_PIN E0_ENABLE_PIN
#define EXT0_ENABLE_ON 0
#define EXT0_MAX_FEEDRATE 300
#define EXT0_MAX_START_FEEDRATE 20
#define EXT0_MAX_ACCELERATION 3000
#define EXT0_HEAT_MANAGER 1
#define EXT0_WATCHPERIOD 1
#define EXT0_PID_INTEGRAL_DRIVE_MAX 210
#define EXT0_PID_INTEGRAL_DRIVE_MIN 40
#define EXT0_PID_PGAIN_OR_DEAD_TIME 20.74
#define EXT0_PID_I 3.19
#define EXT0_PID_D 33.68
#define EXT0_PID_MAX 210
#define EXT0_ADVANCE_K 0
#define EXT0_ADVANCE_L 0
#define EXT0_ADVANCE_BACKLASH_STEPS 0
#define EXT0_WAIT_RETRACT_TEMP 150
#define EXT0_WAIT_RETRACT_UNITS 0
#define EXT0_SELECT_COMMANDS ""
#define EXT0_DESELECT_COMMANDS ""
#define EXT0_EXTRUDER_COOLER_PIN -1
#define EXT0_EXTRUDER_COOLER_SPEED 255
...

Contact Support



Please check out our How-to Guide and FAQ first to see if your question is already answered! :)

If you have a feature request, please add it to this pad. Thanks!


Log in